Plug in an acoustic guitar that sounds great across your lap and the first loud chord can be a surprise. The bass swells, the pick attack gets harder, and the midrange seems to come from a smaller instrument. An EQ pedal gives you a way to work on that amplified sound without changing how you play the guitar.
The BOSS GE-7 is our first choice for a straightforward acoustic board. Its seven bands include useful areas for bass, body and pick attack, and its separate Level slider lets you compare the adjusted sound at a sensible volume. The MXR Ten Band EQ offers a wider spread of frequencies. The BOSS EQ-200 is the more involved choice when you need to recall settings for different guitars. None of these pedals replaces the input stage a passive pickup may need.
The 5 Best EQ Pedals for Acoustic Guitar
1. BOSS GE-7 Equalizer (Editor’s Choice)
The GE-7 starts at 100 Hz and extends to 6.4 kHz, with seven frequency sliders and a separate Level control. That is a useful spread for a single acoustic-electric. You can address a bass-heavy sound, soften a forward midrange, and change the brightness without navigating a screen. BOSS also describes using it as a compact tone-shaping stage for acoustic-electric guitar.
Begin with every slider centered. If a low chord booms through the PA, make a small cut and replay the same chord. Listen to the body of the sound as well as the boom. It is easy to remove the resonance and the useful warmth together. The separate Level slider lets you bring the overall volume back for a fair bypass comparison after making cuts.
The GE-7 is the strongest fit for someone who needs one practical curve for most of a set. It provides up to 15 dB of boost or cut per band, which is more adjustment than most gentle acoustic corrections require. Use that range cautiously. Fixed frequency centers also mean that a very narrow ringing frequency may fall between sliders; an acoustic preamp with a tunable notch filter may be more appropriate for that specific problem.
Pros
- Seven fixed bands with a separate overall Level slider
- Compact format and direct access to every adjustment
- Useful range for the body and attack of amplified acoustic guitar
Cons
- No memory recall for switching between guitars
- Fixed bands do not replace a sweepable narrow notch filter
2. MXR M108S Ten Band EQ
The Ten Band EQ is worth choosing if you already know that the seven-band layout leaves you reaching for more control. It adds frequency coverage and has separate input Gain and output Volume controls. That gives you a way to manage the signal entering and leaving the EQ as well as the curve itself. The silver M108S is the model considered here.
For an acoustic setup, avoid drawing a curve before listening. Start flat, play a low chord, and work upward only as far as the problem requires. Broader frequency coverage is useful when it lets you make a smaller, more appropriate change. It is less useful when it encourages you to adjust ten things just because the sliders are there.
This pedal requires 18-volt power; Dunlop specifies an appropriate adapter and lists one with the product. Check your board’s available outputs rather than treating the M108S like a regular 9-volt pedal. It also has a second output for another signal path. That is handy if you have a defined use for it, but most one-guitar, one-DI rigs should be judged on the basic mono sound and gain setup first.
Pros
- Ten frequency bands and separate input and output level controls
- Wider shaping range than a compact six-band pedal
- Second output for a planned additional signal path
Cons
- Requires the correct 18-volt supply
- Larger control surface and more adjustments than a simple acoustic rig may need
3. BOSS EQ-200 Graphic Equalizer
The EQ-200 makes its case when you switch instruments during a set. It has two ten-band EQ channels, a display of the curve and memory recall. Instead of bending over to restore a group of sliders, you can call up a setting prepared for a second guitar. BOSS offers several frequency-range options, which also makes the pedal more adaptable than a fixed seven-band layout.
Prepare each guitar at a similar performance volume. Start with one curve, save it, switch to the next guitar and build the second from flat. Naming or noting the purpose of each memory is more useful than collecting a dozen nearly identical curves. A fingerstyle guitar with a low output and a hard-strummed acoustic-electric may need different level settings as well as a different tonal balance.
The two channels support several routing arrangements, but those options should solve an actual problem on your board. For a single acoustic into a single input, the extra routing may be unnecessary. The main attraction is repeatable control, and that comes with setup work. Rehearse memory selection with your feet before depending on it for a quiet transition between songs.
Pros
- Recallable curves for different guitars or songs
- Two ten-band channels with flexible routing
- Display makes the saved tonal shape easier to see
Cons
- More setup and menu work than a conventional graphic EQ
- Many functions are unnecessary for one guitar with one basic sound
4. MXR M109S Six Band EQ
The Six Band EQ keeps the job focused. It has six frequency sliders and a compact layout, with up to 18 dB of boost or cut on each band. Dunlop specifically mentions shaping an acoustic pickup’s quacky sound among its uses. For a guitar that needs a little less midrange bite and no elaborate switching, that directness can be appealing.
Unlike the GE-7 and Ten Band EQ, the M109S does not give you a separate overall level slider. When you boost or cut several bands, judge the change at a matched listening level using an appropriate downstream control. Otherwise, a louder setting may seem more flattering than it really is. With acoustic guitar, a few modest cuts are a useful place to start.
Choose the Six Band if you already like most of your amplified tone and want a small set of corrections. It is less attractive if your main problem sits outside its available bands or if you need to swap quickly between curves. It runs on a specified 9-volt battery or suitable supply, which is easier to accommodate on many boards than the M108S’s 18-volt requirement.
Pros
- Compact six-slider layout
- Straightforward adjustment for a mostly satisfactory acoustic sound
- Specified 9-volt power options
Cons
- No independent overall level control
- Fewer frequency choices than the other MXR and BOSS options
5. Behringer EQ700 Graphic Equalizer
The EQ700 offers a conventional seven-band layout with a separate level slider. For a player exploring what an EQ pedal can do, the interface is immediately understandable: center the sliders, change one band, and listen. Its role in this group is a simple way to try practical corrections before committing to a more elaborate EQ setup.
Use it to answer a clear question about your rig. Can a small low-mid cut remove the boxiness that bothers you? Does taking some edge out of the upper range make the pickup easier to listen to? Make the smallest change that answers the question, then compare with bypass at similar volume. A heavily sculpted curve is rarely the best way to learn where the issue lies.
The controls also show the limits of this type of pedal. The EQ700 has fixed bands, no curve memory and no acoustic-specific DI output. If the guitar needs a suitable input preamp, a balanced connection or a narrow feedback notch, those jobs still need to be handled elsewhere. Buy it for adjustable tone shaping rather than expecting a complete acoustic signal path in one box.
Pros
- Familiar seven-band layout
- Separate level slider for comparing adjusted and bypassed sounds
- Direct access to every band
Cons
- No saved curves or acoustic-specific DI
- Fixed frequency choices can miss a narrow troublesome resonance
How to Use an EQ Pedal With Acoustic Guitar
Start flat and find the problem in a real part
Set the guitar’s onboard controls and the PA channel to a sensible starting position. Center the pedal’s sliders and match its engaged level to bypass. Play the actual song instead of a succession of disconnected test notes. A bass-heavy intro and a full strummed chorus can reveal different problems, and the setting must work for the parts you intend to play.
Describe what you hear before moving a slider. Is the low end ringing longer than the chord? Is the sound nasal? Does the pick seem much louder than the note behind it? These descriptions help you choose a direction. They are better guides than copying somebody else’s V-shaped curve.
Reduce boom without making the guitar thin
Try a small cut in the low or low-mid region available on your pedal and replay the chord that caused the problem. A graphic EQ affects a band around its labeled center, so the change will also touch nearby notes. Keep enough body that the instrument still sounds convincing when the bass player stops.
Also check the speaker position and the PA’s high-pass facilities. An EQ pedal may help the tonal balance, but it cannot make every stage position acoustically sensible. If moving away from a speaker fixes the issue with less tonal damage, that is a useful adjustment to make before carving a deep hole in the sound.
Take the edge off a piezo pickup
Play your loudest normal strum and listen to the upper midrange. Try a small cut around the available band that makes the pick attack easier to live with, then return briefly to flat. The comparison matters. It is easy to get used to an increasingly dull sound while trying to remove every trace of pickup character.
A graphic EQ cannot turn one pickup system into another. If a passive pickup is being loaded by an unsuitable input, check the preamp requirements first. If the signal is clipping, reduce gain at the stage where clipping happens. Filtering the result of a distorted input does not restore the clean attack that was lost.
Graphic EQ vs. an Acoustic Preamp
A graphic EQ is a good fit when the existing pickup and input stage already work and you want more direct control over the amplified tone. You can see the adjustments and reach them quickly. A separate EQ also stays useful if you later change your acoustic amplifier or DI.
An acoustic preamp may combine input matching, gain, a balanced output and feedback controls. Those features can be more valuable than extra graphic-EQ bands when the rest of the chain is incomplete. Decide which job needs doing before buying. A passive pickup needing a particular input impedance is a different problem from an active acoustic-electric that simply sounds too forward at a venue.
Can an EQ Pedal Stop Acoustic Feedback?
It can sometimes reduce a troublesome frequency enough to give you usable level. Fixed bands are a limitation when the ringing is very narrow or sits between two centers. A tunable notch filter lets you target a narrow area more precisely, while a graphic EQ may remove more of the guitar’s useful body at the same time.
Keep feedback troubleshooting at a controlled level. Reduce the system volume when ringing starts, check placement, and ask the sound engineer to help identify the cause. Do not keep raising the level while moving every slider. A sound that remains natural at a workable volume is more useful than a dramatic curve that barely holds off feedback.
Where Should an Acoustic EQ Pedal Go?
For an acoustic-electric with an appropriate onboard preamp, placing EQ before modulation and reverb is a practical starting point. This lets the effects receive the corrected guitar sound. A final DI can then provide the connection expected by the mixer. Follow the actual device manuals because an acoustic preamp may already combine EQ, effects routing and a DI.
When you use two guitars, compare their loudest parts before setting output level. A slider position that works for delicate fingerpicking may overload the next input during hard strumming. The GE-7 is the simplest all-round recommendation here; the EQ-200 becomes more useful when you need that level and tonal balance to be recalled reliably for each instrument.




